Error codes for L G washing machines:
1E: Inlet error. Normal water level not reached in 10 minutes. Possible Causes
1. Water tap is shut. Cure Open the tap.
2. Inlet hose is kinked. Cure Repair the inlet hose.
3. Filter on the inlet valve is blocked. Cure Clean/replace the filter.
4. Water pressure is low. Cure Check water pressure.
5. Inlet valve blocked Cure Replace inlet valve.
OE: Drain error (Not fully drained after 5 minutes). possible causes
1. Filter blocked. Check and clean filter.
2. Drain hose kinked or blocked. Check and clear.
3. Drain pump blocked or failed, Unblock or replace
E1: Leakage error Water level in tub decreases during wash
1. Leaking from hoses Check and replace where nessersary
2. Leaking from tub or associated components. Check and replace Part where nessersary
FE Over fill errorOver fill issue. (Drain pump operates automatically).
1. Inlet valve is broken. Check and replace where nessersary
2. Air brake is faulty. Check and replace where nessersary
3. Sensor assembly is faulty. Check and replace where nessersary
4. Controller is faulty. Check and replace where nessersary
TE: Thermal error Thermistor out of calibration, (O/C, S/C).
1. Wiring to the Thermistor is damaged. Check and replace where nessersary
2. Thermistor is out of calibration. Check and replace where nessersary
3. Controller is faulty. Check and replace where nessersary
HE: Heater error. Water has not heated or overheated in the tub.
1. Wiring to the heater is damaged. Check and replace where nessersary
2. Thermistor is faulty. Check and replace where nessersary
3. Heater is S/C or O/C. Check and replace where nessersary
4. The relay circuit is faulty. Check and replace where nessersary
CL: Child Lock error. The Controls have been locked to prevent todlers from changing the program.
Turn of the child lock as per the instruction book.
UE: Unbalance error. The machine is refusing to spin as the wash load is out of balance.
Look for heavy items in the load and remove them, to spin heavy items see our balanced loads article.
SE: Motor error. or possible module fault.
Try replaceing the motor 1st but could be pcb. consider having an engineer repair (repaircare).
CE: Current error. Short circuit to motor or PCB.
Consider having an engineer repair (repaircare).
Error codes for L G Dish Washers:
1E: Inlet error. Normal water level not reached in 10 minutes. Possible Causes
1. Water tap is shut. Cure Open the tap.
2. Inlet hose is kinked. Cure Repair the inlet hose.
3. Filter on the inlet valve is blocked. Cure Clean/replace the filter.
4. Water pressure is low. Cure Check water pressure.
5. Inlet valve blocked Cure Replace inlet valve.
OE: Drain error (Not fully drained after 5 minutes). possible causes
1. Filter blocked. Check and clean filter.
2. Drain hose kinked or blocked. Check and clear.
3. Drain pump blocked or failed, Unblock or replace
E1: Leakage error Water level in tub decreases during wash
1. Leaking from hoses Check and replace where nessersary
2. Leaking from tub or associated components. Check and replace Part where nessersary
FE Over fill errorOver fill issue. (Drain pump operates automatically).
1. Inlet valve is broken. Check and replace where nessersary
2. Air brake is faulty. Check and replace where nessersary
3. Sensor assembly is faulty. Check and replace where nessersary
4. Controller is faulty. Check and replace where nessersary
TE: Thermal error Thermistor out of calibration, (O/C, S/C).
1. Wiring to the Thermistor is damaged. Check and replace where nessersary
2. Thermistor is out of calibration. Check and replace where nessersary
3. Controller is faulty. Check and replace where nessersary
HE: Heater error. Water has not heated or overheated in the tub.
1. Wiring to the heater is damaged. Check and replace where nessersary
2. Thermistor is faulty. Check and replace where nessersary
3. Heater is S/C or O/C. Check and replace where nessersary
4. The relay circuit is faulty. Check and replace where nessersary
L G Tumble Drier error codes.
DE: Door Error. The machine is refusing to start as it thinks the door is open. Check the door lock and catch.
EHE: high temperature and high humidity of air within a
dryer if stopping the dryer in process.
Try to use the dryer again after ventilating air by taking drying all objects and opening the door for more than an hour.
OE: Drain error (Not fully drained after 5 minutes). possible causes
1. Filter blocked. Check and clean filter.
2. Drain hose kinked or blocked. Check and clear.
3. Drain pump blocked or failed, Unblock or replace
E1: Leakage error Water level in tub decreases during wash
1. Leaking from hoses Check and replace where nessersary
2. Leaking from tub or associated components. Check and replace Part where nessersary
TE: Thermal error Thermistor out of calibration, (O/C, S/C).
1. Wiring to the Thermistor is damaged. Check and replace where nessersary
2. Thermistor is out of calibration. Check and replace where nessersary
3. Controller is faulty. Check and replace where nessersary
HE: Heater error. Water has not heated or overheated in the tub.
1. Wiring to the heater is damaged. Check and replace where nessersary
2. Thermistor is faulty. Check and replace where nessersary
3. Heater is S/C or O/C. Check and replace where nessersary
4. The relay circuit is faulty. Check and replace where nessersary
CL: Child Lock error. The Controls have been locked to prevent todlers from changing the program.
Turn of the child lock as per the instruction book.
DE: Door Error. The machine is refusing to start as it thinks the door is open. Check the door lock and catch.
Look for heavy items in the load and remove them, to spin heavy items see our balanced loads article.
SE: Motor error. or possible module fault.
Try replaceing the motor 1st but could be pcb. consider having an engineer repair (repaircare).
CE: Current error. Short circuit to motor or PCB.
Consider having an engineer repair (repaircare).
Hotpoint washing machine Fault codes
Error codes for L G washing machines:
1E: Inlet error. Normal water level not reached in 10 minutes. Possible Causes
1. Water tap is shut. Cure Open the tap.
2. Inlet hose is kinked. Cure Repair the inlet hose.
3. Filter on the inlet valve is blocked. Cure Clean/replace the filter.
4. Water pressure is low. Cure Check water pressure.
5. Inlet valve blocked Cure Replace inlet valve.
OE: Drain error (Not fully drained after 5 minutes). possible causes
1. Filter blocked. Check and clean filter.
2. Drain hose kinked or blocked. Check and clear.
3. Drain pump blocked or failed, Unblock or replace
E1: Leakage error Water level in tub decreases during wash
1. Leaking from hoses Check and replace where nessersary
2. Leaking from tub or associated components. Check and replace Part where nessersary
FE Over fill errorOver fill issue. (Drain pump operates automatically).
1. Inlet valve is broken. Check and replace where nessersary
2. Air brake is faulty. Check and replace where nessersary
3. Sensor assembly is faulty. Check and replace where nessersary
4. Controller is faulty. Check and replace where nessersary
TE: Thermal error Thermistor out of calibration, (O/C, S/C).
1. Wiring to the Thermistor is damaged. Check and replace where nessersary
2. Thermistor is out of calibration. Check and replace where nessersary
3. Controller is faulty. Check and replace where nessersary
HE: Heater error. Water has not heated or overheated in the tub.
1. Wiring to the heater is damaged. Check and replace where nessersary
2. Thermistor is faulty. Check and replace where nessersary
3. Heater is S/C or O/C. Check and replace where nessersary
4. The relay circuit is faulty. Check and replace where nessersary
CL: Child Lock error. The Controls have been locked to prevent todlers from changing the program.
Turn of the child lock as per the instruction book.
UE: Unbalance error. The machine is refusing to spin as the wash load is out of balance.
Look for heavy items in the load and remove them, to spin heavy items see our balanced loads article.
SE: Motor error. or possible module fault.
Try replaceing the motor 1st but could be pcb. consider having an engineer repair (repaircare).
CE: Current error. Short circuit to motor or PCB.
Consider having an engineer repair (repaircare).
Error codes for L G Dish Washers:
1E: Inlet error. Normal water level not reached in 10 minutes. Possible Causes
1. Water tap is shut. Cure Open the tap.
2. Inlet hose is kinked. Cure Repair the inlet hose.
3. Filter on the inlet valve is blocked. Cure Clean/replace the filter.
4. Water pressure is low. Cure Check water pressure.
5. Inlet valve blocked Cure Replace inlet valve.
OE: Drain error (Not fully drained after 5 minutes). possible causes
1. Filter blocked. Check and clean filter.
2. Drain hose kinked or blocked. Check and clear.
3. Drain pump blocked or failed, Unblock or replace
E1: Leakage error Water level in tub decreases during wash
1. Leaking from hoses Check and replace where nessersary
2. Leaking from tub or associated components. Check and replace Part where nessersary
FE Over fill errorOver fill issue. (Drain pump operates automatically).
1. Inlet valve is broken. Check and replace where nessersary
2. Air brake is faulty. Check and replace where nessersary
3. Sensor assembly is faulty. Check and replace where nessersary
4. Controller is faulty. Check and replace where nessersary
TE: Thermal error Thermistor out of calibration, (O/C, S/C).
1. Wiring to the Thermistor is damaged. Check and replace where nessersary
2. Thermistor is out of calibration. Check and replace where nessersary
3. Controller is faulty. Check and replace where nessersary
HE: Heater error. Water has not heated or overheated in the tub.
1. Wiring to the heater is damaged. Check and replace where nessersary
2. Thermistor is faulty. Check and replace where nessersary
3. Heater is S/C or O/C. Check and replace where nessersary
4. The relay circuit is faulty. Check and replace where nessersary
L G Tumble Drier error codes.
DE: Door Error. The machine is refusing to start as it thinks the door is open. Check the door lock and catch.
EHE: high temperature and high humidity of air within a
dryer if stopping the dryer in process.
Try to use the dryer again after ventilating air by taking drying all objects and opening the door for more than an hour.
OE: Drain error (Not fully drained after 5 minutes). possible causes
1. Filter blocked. Check and clean filter.
2. Drain hose kinked or blocked. Check and clear.
3. Drain pump blocked or failed, Unblock or replace
E1: Leakage error Water level in tub decreases during wash
1. Leaking from hoses Check and replace where nessersary
2. Leaking from tub or associated components. Check and replace Part where nessersary
TE: Thermal error Thermistor out of calibration, (O/C, S/C).
1. Wiring to the Thermistor is damaged. Check and replace where nessersary
2. Thermistor is out of calibration. Check and replace where nessersary
3. Controller is faulty. Check and replace where nessersary
HE: Heater error. Water has not heated or overheated in the tub.
1. Wiring to the heater is damaged. Check and replace where nessersary
2. Thermistor is faulty. Check and replace where nessersary
3. Heater is S/C or O/C. Check and replace where nessersary
4. The relay circuit is faulty. Check and replace where nessersary
CL: Child Lock error. The Controls have been locked to prevent todlers from changing the program.
Turn of the child lock as per the instruction book.
DE: Door Error. The machine is refusing to start as it thinks the door is open. Check the door lock and catch.
Look for heavy items in the load and remove them, to spin heavy items see our balanced loads article.
SE: Motor error. or possible module fault.
Try replaceing the motor 1st but could be pcb. consider having an engineer repair (repaircare).
CE: Current error. Short circuit to motor or PCB.
Consider having an engineer repair (repaircare).
L G Fridge and Freezer Error Codes
.
FF: Error Code. This indicates a problem with the Freezer Fan rotateing.
If the fan has been "whirring" for some time and has now stopped it may be due to ice build up catching the blades.
Try Defrosting by switching of for 48 hours with the door open on the freezer. if this cures the fault but problem returns it may be due to a defrost problem.
FS: Error Code. Freezer Sensor Problem
Try powering off and on to see if problem clears. if continuose you may need to replace sensor.
RS: Error Code. Fridger Sensor Problem
Try powering off and on to see if problem clears. if continuose you may need to replace sensor.
DS: Error Code. Defrost Sensor Problem
Try powering off and on to see if problem clears. if continuose you may need to replace sensor.
DH: Error Code. Defrost Heater Problem
Try powering off and on to see if problem clears. if continuose you may need to replace sensor.
CF: Error Code. Cooling Fan Problem
Try powering off and on to see if problem clears. if continuose you may need to replace the cooling fan near the compresor at the back.
CO: Error Code. Communication Problem
This is due to the control boards not "talking" to each other. Try powering off and on to see if problem clears. if continuose you may need to replace the Boards.
If a code only occurs occasionally it may be not a fault with the machine but for example a balance error code may be due to incorrect loading of the machine.
However some errors may only show on certain cycle for example a heating error on washing may not show on a low temperature cycle.
It may be that you find your machine having drained and not completed the cycle showing an error code, if this is the case and the code is not known or vague then try starting a short cycle empty on a high temperature. Then by keeping an eye on the machine you will be able to check if it fills, starts washing, heats (after 15 minutes or so), empty' s and then spins. If there is a fault then one of these steps may not complete and the programme may stop or finish prematurely.
For example if the machine fills washes heats but struggles to empty (water still in after several minutes draining). It can be seen that the pump is trying to drain and the problem is likely to be an obstruction or partial blockage (typically a sock or debris in the filter).
.
Washing Machine advice articles:
Diagnosing a faulty washing machine
<
If a code only occurs occasionally it may be not a fault with the machine but for example a balance error code may be due to incorrect loading of the machine.
However some errors may only show on certain cycle for example a heating error on washing may not show on a low temperature cycle.
It may be that you find your machine having drained and not completed the cycle showing an error code, if this is the case and the code is not known or vague then try starting a short cycle empty on a high temperature. Then by keeping an eye on the machine you will be able to check if it fills, starts washing, heats (after 15 minutes or so), empty' s and then spins. If there is a fault then one of these steps may not complete and the programme may stop or finish prematurely.
For example if the machine fills washes heats but struggles to empty (water still in after several minutes draining). It can be seen that the pump is trying to drain and the problem is likely to be an obstruction or partial blockage (typically a sock or debris in the filter).
.
Error codes for L G Dish Washers:
1E: Inlet error. Normal water level not reached in 10 minutes. Possible Causes
1. Water tap is shut. Cure Open the tap.
Error codes for L G Dish Washers:
1E: Inlet error. Normal water level not reached in 10 minutes. Possible Causes
1. Water tap is shut. Cure Open the tap.
Error codes for L G Dish Washers:
1E: Inlet error. Normal water level not reached in 10 minutes. Possible Causes
1. Water tap is shut. Cure Open the tap.
..
L G Tumble Drier error codes.
DE: Door Error. The machine is refusing to start as it thinks the door is open. Check the door lock and catch.
EHE: high temperature and high humidity of air within a
dryer if stopping the dryer in process.
Try to use the dryer again after ventilating air by taking drying all objects and opening the door for more than an hour.
L G Tumble Drier error codes.
DE: Door Error. The machine is refusing to start as it thinks the door is open. Check the door lock and catch.
EHE: high temperature and high humidity of air within a
dryer if stopping the dryer in process.
Try to use the dryer again after ventilating air by taking drying all objects and opening the door for more than an hour.
₤
(change)
